热门关键词:
位置:首页 > 成套图纸
拨叉(12-07-05)加工全套本科毕业设计
  • 该文件为rar格式
  • 文件大小: 1.59 MB
  • 下载次数
  • 文件评级
  • 更新时间:2014-08-07
  • 发 布 人: 2303143778
  • 文件下载:
  • 立即下载

  • 文件介绍:
  • 该文件为 rar 格式(源文件可编辑),下载需要 20 积分
  • 拨叉(12-07-05)加工全套本科毕业设计
  • 拨叉(12-07-05)加工全套本科毕业设计
    摘 要

    此次设计是对拨叉零件的加工工艺和夹具设计,其零件为锻件,具有体积小,零件复杂的特点,由于面比孔易加工,在制定工艺规程时,就先加工面,再以面为基准来加工其它,其中各工序夹具都采用专用夹具,特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中,选一面两销的定位方式,并以操作简单的手动夹紧方式夹紧,其机构设计简单,方便且能满足要求。


    关键词 拨叉,加工工艺,专用夹具,设计
    ABSTRACT

    This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.


    Key words: Dials the fork, the processing craft, unit clamp, design

    目 录

    摘 要 I
    ABSTRACT Ⅱ
    1 绪 论 1
    2 拨叉的分析 2
    2.1拨叉的工艺分析 2
    2.2拨叉的工艺要求 2
    3工艺规程设计 5
    3.1 加工工艺过程 5
    3.2确定各表面加工方案 5
    3.2.1影响加工方法的因素 5
    3.2.2加工方案的选择 6
    3.3 确定定位基准 6
    3.2.1粗基准的选择 6
    3.2.1精基准选择的原则 7
    3.4工艺路线的拟订 7
    3.4.1工序的合理组合 8
    3.4.2工序的集中与分散 8
    3.4.3加工阶段的划分 9
    3.4.4加工工艺路线方案的比较 10
    3.5拨叉的偏差,加工余量,工序尺寸及毛坯尺寸的确定 12
    3.5.1毛坯的结构工艺要求 12
    3.5.2拨叉的偏差计算 12
    3.6确定切削用量及基本工时(机动时间) 14
    3.7时间定额计算及生产安排 22
    4 镗孔夹具设计 25
    4.1 研究原始质料 25
    4.2 定位、夹紧方案的选择 25
    4.3切削力及夹紧力的计算 25
    4.4 误差分析与计算 27
    4.5 零、部件的设计与选用 28
    4.5.1定位销选用 28
    4.5.2夹紧装置的选用 29
    4.6 夹具设计及操作的简要说明 29
    5 铣槽夹具设计 30
    5.1研究原始质料 30
    5.2定位基准的选择 30
    5.3 切削力及夹紧分析计算 30
    5.4 误差分析与计算 32
    5.5 零、部件的设计与选用 33
    5.5.1定位销选用 33
    5.5.2夹紧装置的选用 33
    5.5.3 定向键与对刀装置设计 33
    5.6 夹具设计及操作的简要说明 36
    6 钻孔夹具设计 37
    6.1研究原始质料 37
    6.2定位基准的选择 37
    6.3切削力及夹紧力的计算 37
    6.4误差分析与计算 38
    6.5 零、部件的设计与选用 39
    6.5.1定位销选用 39
    6.5.2夹紧装置的选用 40
    6.5.3 钻套、衬套、钻模板设计与选用 40
    6.6夹具设计及操作的简要说明 41
    结 论 42
    参考文献 43
    致 谢 44 ...
文档留言 共有条评论
验证码: 请在右侧输入验证码 看不清楚,换一个
拨叉(12-07-05)加工全套本科毕业设计_下载(rar格式) 成套图纸